- Since with this type of loading of the laminate, energy is released in the form of heat, it is often possible to test only with very low frequencies of up to approximately 5 Hz. Recording an entire durability curve is therefore very time consuming.
- ZwickRoell offers load frames with various drive concepts for dynamic testing. Testing machines with electrical linear motor drives are used for lower test loads up to 10 kN. These testing machines, which can generate frequencies up to 100 Hz, are very clean, produce little noise, and require minimum service.
- Servohydraulic testing machines in various sizes are available for tests with both small and large loads.
-
Industries
(Show submenu)
- Materials Testing
-
Plastics
(Show submenu)
-
Thermoplastics and thermosetting molding materials
(Show submenu)
- Tensile Tests on Plastics
- Tensile Tests on Plastics
- Tensile tests at high strain rates
- Notched Charpy impact test on plastics
- Izod impact test plastics
- Notched Izod impact strength plastics
- Tensile impact test plastics
- Plastics puncture test
- 3-point flexure test plastics
- 3-point flexure test plastics
- Melt flow index test plastics
- Determination of HDT VST plastics
- Hardness tests plastics
- Creep test plastics
- Automation plastics
- Intermediate products and finished parts (Show submenu)
- Thin sheeting and plastic films (Show submenu)
- Testing hard and soft polymer foams (Show submenu)
- Plastic Pipes (Show submenu)
-
Thermoplastics and thermosetting molding materials
(Show submenu)
-
Composites
(Show submenu)
- Tensile tests
- Compression tests and notched compression tests (Show submenu)
- Compression after impact CAI
- Flexure tests
- Alignment
- Interlaminar shear strength ILSS
- Shearing through overlapping
- In-plane shear (IPS)
- V-notched shear test
- Energy release rate (G)
- Dynamic cyclic test methods
- Testing at cryogenic temperatures
-
Metals
(Show submenu)
-
Metals standards
(Show submenu)
- Tensile test on metals
- Tensile tests metals
- Tensile test on metals at elevated temperature
- Tensile test on metals
- Rockwell test metals
- Vickers test metals
- Brinell test metals
- r-value metals
- n-value metals
- Fracture mechanics: crack growth da/dN and threshold value
- Fracture mechanics: critical stress intensity factor K1C
- Notched Charpy impact test metals
- Notched Charpy impact test metals
- Concrete-reinforcing steel, EN ISO 15630-1, ASTM E488, BS 4449
- Welded mats / lattices ISO 15630-2
- Steel strands ISO 15630-3, ASTM A416, ASTM A1061
- Flat Products (Show submenu)
- Long products (Show submenu)
- Semi-finished products (Show submenu)
- Pipes
-
Metals standards
(Show submenu)
- Automotive (Show submenu)
-
Medical/Pharmaceutical
(Show submenu)
- United States Pharmacopeia
- Therapy systems (Show submenu)
- Catheters and stents (Show submenu)
- Biomaterials and clinical research (Show submenu)
- Dental Industry (Show submenu)
-
Hip implants
(Show submenu)
- Endurance properties testing stemmed femoral components and neck region of stemmed femoral components
- Compression/pull-off test femoral head
- Deformation test method acetabular shell
- Torsion test femoral head
- Forces for disassembly of acetabular shell / liner
- Tensile test femoral head
- Fatigue strength ceramic femoral heads
- Fatigue testing modular femoral stems
- Biomechanics and Orthopedics (Show submenu)
- Latex, Rubber, Silicone (Show submenu)
- Medical textile products (Show submenu)
- Surgical instruments
- Medical packaging (Show submenu)
- Automated tests
- Academia
- Energy (Show submenu)
- Paper, Cardboard, Tissues (Show submenu)
- Food & Packaging
- Textiles
- Mechatronics – Electronics
- Building Materials
- Springs
-
Products
(Show submenu)
- Static Materials Testing Machines (Show submenu)
- Dynamic and Fatigue Testing Systems (Show submenu)
- Automated Testing Systems (Show submenu)
- Products for Impact Testing
- Extrusion Plastometers / Melt Flow Index Testers (Show submenu)
- HDT and Vicat Testing Instruments (Show submenu)
- Hardness testing machines (Show submenu)
- Modernization of Testing Systems (Show submenu)
- testXpert
-
Accessories
(Show submenu)
- testXpert testing software
- Measurement and control electronics
- Xforce Load Cells
- Specimen Grips
- Test Tools
- Extensometers (Show submenu)
- Temperature and climate
- Specimen preparation and dimensional measurement
- Accessories online
- Services (Show submenu)
- Company (Show submenu)
- Careers (Show submenu)
- Resources & Events